DGNStyler
Prepares features for output to Bentley Microstation Design V7/V8 by providing a convenient interface to set a variety of Bentley Microstation Design format-specific attributes.
参数 - 颜色
Specifies that the pen color will be set by the color of the level specified on an FME Feature, rather than by the RGB color or Index color. (Note that this parameter is only supported by the V8 version of the Design writer.)
Format attribute set:igds_color_set_bylevel
Specifies format of the color to use. This applies to both the pen color and the fill color which are together used to render the feature.
Specifies the pen color that will be used to render the feature. The pen color determines the color of lines, and area boundaries. To edit this parameter, click the browse button to the right of the text field.
Format attribute set:fme_color
Note:Note that when this parameter is specified, theigds_colorattribute is removed from the feature andfme_coloris set. This is becauseigds_coloroverridesfme_colorif they are both present.
Note:另请注意,RGB颜色指定fme_colormay be stored as the color table index which most closely approximates it, where the color table is defined as a specific set of RGB colors in the seed file.
Specifies the fill color that will be used for the feature. The fill color determines the color used within the boundary of area features. To edit this parameter, click the browse button to the right of the text field.
Format attribute set:fme_fill_color
Note:Note that when this parameter is specified, theIGDS_FILL_COLOR.attribute is removed from the feature andfme_fill_coloris set. This is becauseIGDS_FILL_COLOR.overridesfme__fill_colorif they are both present.
Note:另请注意,RGB颜色指定fme_colormay be stored as the color table index which most closely approximates it, where the color table is defined as a specific set of RGB colors in the seed file.
Specifies the index of a pen color in a table of colors. The indexed color will be used for the feature. The pen color determines the color of lines, and area boundaries. This parameter can be set to integer value between 0 and 255.
Format attribute set:igds_color
Specifies the index of a fill color in a table of colors. The indexed color will be used for the feature. The fill color determines the color used within the boundary of area features. This parameter can be set to integer value between 0 and 255.
Format attribute set:IGDS_FILL_COLOR.
参数 - 细胞
If this section is active, point features will be turned into cells and given a cell name, rotation, and size.
Features with other geometry types will not be affected by settings in this section.
Format attributes set:igds_type来igds_cellorIGDS_SHARED_CELL.
指定将由变压器作为单元名的源代码使用的现有Bentley MicroStation设计单元文件的名称。实际设计编写器不使用它 - 必须在Writer的参数中指定单元库文件,并且应包含与此处指定的文件相同的单元名。最常情况下,相同的文件将用于变压器和作者。另外注意,如果不使用单元格,则该参数可以留空。
Specifies the cell that will be placed at the point location. Click the browse button to pick the name from the set of cells defined in the cell library file.
Format attribute set:igds_cell_name
Specifies how a cell will be written. If a value of Library is specified, anigds_cell预计参考创建元素a cell definition in the cell library file. Otherwise, if a value of Shared (V8 Only) is specified, then anIGDS_SHARED_CELL.element is created in the destination which does not refer to a cell definition in the cell file definition. (Note that the Shared value for this parameter is only supported by the V8 version of the Design writer.)
Format attribute set:igds_type来igds_cellorIGDS_SHARED_CELL.
Specifies if the graphic cells are to be created as relative graphic cells. Relative graphic cells map the cell members with the lowest level number to the current cell feature's level which becomes a base level for the relative graphic cell. All the subsequent cell members have their levels offset according to the base level. This does not apply to point or shared cells. (Note that this parameter is only supported by the V8 version of the Design writer.)
Format attribute set:igds_is_graphic_cell_relative
Specifies rotation of the cell (in degrees counterclockwise from horizontal). This can be set to any floating point value between -360.0 to 360.0, or be set to a value taken from an attribute.
Format attribute set:igds_cell_rotation
表示将如何指定单元格的大小。如果选择了主单元,则将缩放单元格,以便其在x,y和z中的范围涵盖指定的量。如果选择比例因子,则x,y和z中的量指定将应用于三个轴中的每一个中的小区的缩放。
指定X轴的调整量,可以是浮点值或从属性中获取。其含义通过上述设置取决于块大小。
Format attributes set:igds_cell_x_scale(if Cell Size By is Scale Factor);igds_cell_size_x(if Cell Size By is Master Units)
Specifies the sizing amount for the y axis, which can be a floating point value or taken from an attribute. Its meaning is dependent on the Block Size By setting described above.
Format attributes set:igds_cell_y_scale(if Cell Size By is Scale Factor);igds_cell_size_y(if Cell Size By is Master Units)
Specifies the sizing amount for the z axis, which can be a floating point value or taken from an attribute. Its meaning is dependent on the Block Size By setting described above.
Format attribute set:igds_cell_z_scale(if Cell Size By is Scale Factor)
参数 - 行
If this section is active, then linear features will be prepared for output to Bentley Microstation Design.
Features with other geometry types will not be affected by settings in this section.
Specifies an index in the range 0 to 31 which designates the width or thickness of the lines used to render a graphic element. In addition, the line weight may be set to ByLevel, which specifies that the line weight be set by the level specified on an FME Feature. Click the browse button to pick from a visual representation of the possible values.
Format attribute set:igds_weightandIGDS_WEIGHT_SET_BYLEVEL.
Specifies an index in the range 0 to 7 which designates the style of the lines used to render a graphic element. In addition, the line style may be set to ByLevel, which specifies that the line style be set by the level specified on an FME Feature. Click the browse button to pick from a visual representation of the possible values.
Format attribute set:igds_styleandigds_style_set_bylevel
Parameters – Text
If this section is active, then text features will be prepared for output to Bentley Microstation Design.
Features with other geometry types will not be affected by settings in this section.
Specifies the font that will be used for the text. Values from 0..511 are RSC fonts, while values from 512..1023 are SHX fonts, and values above 1023 are True Type fonts.
Format attribute set:igds_font
指定的IDtextstyle that will be used. If a matching ID is found in the seed file, then that text style information will be applied to this text element as the default style.
Any text style options set here will take precedence over the matched default text style information.
Format attribute set:igds_textstyle_id
Specifies the size of the text, measured in ground units. This is stored as the height of the text element.
Format attribute set:fme_text_size
指定在地面单元中测量的文本的宽度。如果未指定此参数,则Bentley MicroStation设计作家使用Text Size.
Format attribute set:igds_text_width_multiplier
设置文本的正义代码。
Format attribute set:igds_justification
Specifies the rotation of the text string. The rotation is measured in degrees counterclockwise up from the horizontal.
Format attribute set:fme_rotation
Specifies whether or not the text should have a bold style.
Format attribute set:igds_textstyle_bold.
Specifies whether or not the text should have an italic style and the angle in degrees at which the text will slant.
An angle of 30 degrees is usually used to apply an italic style.
Format attribute set:igds_textstyle_slant.
Specifies whether or not the text should have an underline style.
Format attribute set:igds_textstyle_underline
Specifies whether or not the text should have an overline style.
Format attribute set:igds_textstyle_overline
Additional References
For more information about styling:
- SeeBentley Microstation Design Reader/Writer > Feature Representation在里面FME Readers and Writersmanual. In Workbench, select Help > FME Readers and Writers Reference.
Editing Transformer Parameters
Using a set of menu options, transformer parameters can be assigned by referencing other elements in the workspace. More advanced functions, such as an advanced editor and an arithmetic editor, are also available in some transformers. To access a menu of these options, clickbeside the applicable parameter. For more information, seeTransformer Parameter Menu Options.
Transformer Categories
搜索FME知识中心
搜索有关此变压器的样本和信息FME Knowledge Center.