VoronoiCellGenerator
输出的对于具有由方位角定义的方向指向特性影响圆形扇区(度从北顺时针)。
该变压器为每一组的指向特性(统称为创建若干个扇区现场),这取决于影响每个点的方向。从中心点各部门扇出(本站点)站点的它属于,且具有用户定义的半径。
该变压器产生由代表围绕部门(部位点)的中心点最接近的区域多边形的Voronoi图。最后的输出将被截断为自己网站的相应的Voronoi多边形的范围的部门。
这个变压器具有产生通过的Voronoi多边形截头扇形的附加输出端口,以消除不同位点之间可能的重叠。
Note:要创建可以与其他网站的部门重叠的部门,使用SectorGenerator变压器代替。
输入端口
这种变压器只接受点。所有其他几何形状将被拒绝。
如果3D点进入这个变压器,他们就好像它们是2D点处理。
输出端口
行业多边形是通过此端口正常曝光的输出。不同位点的输出扇区可彼此重叠。
这些是由变压器产生的,并用于夹的输出多边形的Voronoi多边形细胞港口。
对于每个站点,这一点与那些平均接受了该部门所有的坐标点的坐标创建。这一点对于一个网站产生的所有部门的中心。
如果指定了部门名称属性,并有与同一部门和站点名称的点,只有满足所有的要求被认为是创造部门,其余的第一点是从该端口输出。
在进入变压器,如果一个点被发现是从任何其他点更远在其网站比规定Maximum Distance Between Site Points,它将从部门的生成和输出从该端口被丢弃。
参数
这是确定哪个输入点所属的站点的属性。
方向的每个输入点的面(或影响)。方位角属性以度从北顺时针测量。有效方位属性值为正且小于360。
如果一个部门名称属性指定 are points with the same sector name in a site, only one of the points is considered for creating sectors.
Each feature entering the transformer is checked.If its sector name is already in use within its site, it will be output on theExtraPoints港口。
This parameter defines the radius of influence for each sector.This determines the radius of each sector in a site.
Note:Values of Radii larger than the extents of the area covered by the site points will produce invalid results.Differing values of radii for overlapping sectors will also result in incorrect output.
This parameter specifies the maximum distance a point can be from any other point in its site and still be considered in sector creation.
Points are considered in the order they enter the transformer, with each new point tested against all other points already accepted as a part of its site.
If a nonconstant value is specified for this parameter (for example, an attribute value, which may differ from feature to feature), then when comparing the distance between two features, the maximum distance will be calculated from the feature that entered the transformer earlier.
No:There may be slight overlaps or gaps between sectors, making the output unsuitable for some geometric operations.
Note that the input points should be in a way that the transformer is able to produce at least three different site points that are not collinear, since a Voronoi Diagram is generated for analysis.
例
在电信行业,定向天线一起使用的彼此对更好的覆盖和更强的信号接收。这些天线每盖一个完整的圆的扇区天线塔盖,每两个部门之间的重叠部分地区。
该变压器可用于确定定向天线和接收器的“目标”(假设一个整圈覆盖并有任意两个扇区之间没有重叠)的覆盖场。
输入点和它们的方位值接收:
为每个站点创建一个中心观点:
Note:请注意,这一步之后,输入点的位置在行业的产生没有用武之地,并决定行业的值是输入点方位角和半径。
多边形部门产生。对应于各点的扇区将跨越由半径集和确定的面积:
(该点的方位角+相邻方位(以度为单位))/ 2
一个部门的两侧通过一次选择最接近的方位顺时针和逆时针下一次发现。导致行业将是这样的:
的Voronoi多边形生成,根据现场几点:
如果两个网站都重叠的部门,该部门通过的Voronoi多边形生成细胞剪辑:
FME许可级别
FME专业版及以上
编辑变压器参数
使用一组菜单选项,变压器参数可以通过引用在工作区中的其它元件来分配。更先进的功能,如高级编辑,算术编辑,也是一些变压器可用。要访问这些选项的菜单,点击适用的参数旁边。欲了解更多信息,请参阅变压器参数菜单选项。
变压器分类
FME社亚搏国际在线官网区
该FME社区是为亚搏国际在线官网演示,入门指南,文章,FAQ,以及更多的地方。解答您的问题,向其他用户学习,并建议,投票,并在新的功能注释。
搜索样品和有关该变压器的FME社亚搏国际在线官网区。